Parts of a Lamp: A Labeled Guide to Every Component
Residence Supply |
A lamp looks simple until something stops working, or a new shade refuses to sit straight. That's usually when people go looking for the names of the parts of a lamp, because you can't buy a replacement harp or socket if you don't know what to call it.
Quick answer: Every table or floor lamp is built from three groups of parts. The electrical parts (socket, switch, cord, plug and bulb) make the light. The structural parts (base, body, neck and the threaded rod inside) hold everything together. The shade hardware (harp, saddle, fitter and finial) holds the lampshade in place.
Parts of a Lamp Diagram (Table and Floor Lamp)
The diagram below labels the parts you'll find on a typical table lamp with a harp and a spider-fitter shade. A floor lamp uses the same parts with a taller body and a heavier base, so the labels apply to both.
| Part | What it does | Where it sits | Easy to replace? |
|---|---|---|---|
| Finial | Locks the shade onto the harp | Top of the harp | Yes |
| Harp | Holds the shade above the bulb | Clips into the saddle | Yes |
| Shade | Diffuses light and hides the bulb | Rests on the harp or socket | Yes |
| Bulb | Produces the light | Screws into the socket | Yes |
| Socket | Holds the bulb and connects it to power | Top of the neck | Yes, with care |
| Switch | Turns the light on and off | On the socket, cord or base | Yes, with care |
| Saddle | Supports the harp | Under the socket | Yes |
| Neck | Short tube that raises the socket | Between body and socket | Sometimes |
| Body | The main decorative column | Middle of the lamp | No |
| Threaded rod | Holds the lamp together and carries the cord | Runs through the body | Sometimes |
| Base | Keeps the lamp stable | Bottom of the lamp | No |
| Cord and plug | Bring power from the outlet | Exit at the base | Yes, with care |
Electrical Parts of a Lamp
The electrical parts are the ones that turn power from your wall outlet into light. They're also the parts most likely to wear out, so they're worth knowing by name.
Socket: Shell, Insulating Sleeve and Interior
The socket holds the light bulb and connects it to the lamp's wiring. On most lamps it has three layers. The outer shell is the metal or plastic casing you see. Inside it sits an insulating sleeve, a collar that fits into the shell to prevent short circuits. The interior is the threaded cup the bulb screws into, with the screw terminals the cord wires attach to.
If a bulb flickers when you tap the lamp, the socket is often the first part to check.
Lamp Switch Types: Turn Knob, 3-Way, Pull Chain, Rotary and In-Line
A lamp switch can live on the socket, on the base or on the cord. Common versions include rotary, push-button, turn-knob, canopy, pull-chain and toggle switches. An in-line switch sits partway along the cord, which is handy when the socket is hard to reach.
| Switch type | Where you'll find it | Best for |
|---|---|---|
| Turn knob | Built into the socket | Classic table lamps |
| Push-through | Built into the socket | Simple on/off |
| Pull chain | Hangs from the socket | Floor lamps and older fixtures |
| Rotary | On the cord or base | Lamps with a dimming option |
| In-line | Partway along the cord | Lamps with hard-to-reach sockets |
| 3-way | Built into the socket | Three brightness levels |
How a 3-Way Lamp Socket Works
A 3-way lamp gives you three brightness levels from one bulb. A 3-way incandescent bulb has two filaments that can be switched on separately or together. A common example is the 50/100/150 W bulb, which pairs a 50 W filament with a 100 W filament.
The socket has three electrical contacts instead of two. The extra one matches a ring-shaped contact on the bottom of a 3-way bulb. Put a standard bulb in a 3-way socket and it will only light on one or two of the clicks, because the ring contact has nothing to touch.
This is a different thing from a 3-way wall switch, which controls one ceiling light from two locations. If that's what you're wiring, the 3-way light switch wiring guide walks through it step by step.
Cord and Polarized Plug
The cord carries electricity from the outlet up through the lamp to the socket. Look at the plug on most modern lamps and you'll see one blade is wider than the other. That's a polarized plug, designed to help keep electricity from leaking to the metal parts of the lamp.
Inside the socket, many lamps also have an Underwriter's knot (UL knot) tied in the cord. It gives strain relief to the screw terminals, so a tug on the cord doesn't pull the wires loose.
Bulb and Bulb Base (E26, E12)
The bulb is the only part you'll replace regularly, and the base is what decides whether it fits. The "E" in a base code stands for Edison screw, and the number is the base diameter in millimeters. E26 is the standard medium base used in most North American lamps, while E12 is the smaller candelabra base, about 12 mm across, used mostly for decorative lighting.
For shapes, color temperature and brightness, see the guide to choosing the right light bulbs.
Structural Parts: Base, Body, Neck and Threaded Rod
The structural parts carry the lamp's weight and give it its look. Most of them are threaded onto one hidden rod, which is why a wobbly lamp can usually be fixed by tightening a single nut underneath.
Base and Felt Pad
The base is the bottom of the lamp and its main job is stability. Floor lamps need a wider, heavier base than table lamps because they're tall and easy to knock. Underneath, many lamps have a felt pad that protects furniture from scratches and covers the nut that holds the lamp together.
Body or Column
The body (also called the column) is the decorative middle of the lamp. It's the part that defines the style, whether that's a ceramic gourd, a glass column or a brass stem. If you're comparing materials, brass and alabaster each age and diffuse light differently.
Neck, Check Ring and Vase Cap
Between the body and the socket you'll often find a short neck, a decorative tube that lifts the socket to the right height. A check ring is a small ring that sits on the threaded rod and finishes off a joint. A vase cap sits over the opening of a vase-style body, so the rod and cord can pass through cleanly.
Threaded Rod (Lamp Pipe), Locknut and Washers
Hidden inside nearly every lamp is a hollow threaded rod, also called lamp pipe. It typically anchors the lamp together, with the other parts threaded onto it, and the cord runs up through its center.
The most common size is 1/8 IP, which has a 3/8 inch outside diameter. Its thread is always 27 threads per inch. Larger 1/4 IP pipe, with a 1/2 inch outside diameter, shows up on floor lamps and floor lamp bases. A locknut and washers at the bottom of the rod clamp everything tight.
| Thread size | Outside diameter | Where it's used |
|---|---|---|
| 1/4-27 | 7/32 inch | Harp tops and most finials |
| 1/8 IP | 3/8 inch | Most table lamp rods, necks and sockets |
| 1/4 IP | 1/2 inch | Floor lamps and floor lamp bases |
Lampshade Parts and Fitters
The shade hardware is where most "why won't this shade fit?" problems start. A fitter is the metal framework inside the top of a shade that attaches it to the lamp, harp or socket. There are three main types, and each one needs different hardware on the lamp.
Lamp Harp and Saddle
A lamp harp is the U-shaped metal frame that arcs over the bulb and holds the shade. Its legs clip into a saddle, the part that sits on the lamp just below the socket.
Harps come in different heights, and the right one lets the shade cover the socket and bulb without touching the base. To size one, measure from the saddle to the top of the harp. If your shade sits too high and shows the socket, a shorter harp is usually the fix.
Finial: The Top of the Lamp
The piece at the very top of a lamp is the finial. It's a decorative fitting that secures the shade to the harp. Most finials screw onto a 1/4-27 thread, which is why they're easy to swap for a different style. For the history and design side of finials, see finials explained.
Spider vs Uno vs Clip-On Fitters
Check what your lamp has before you buy a new shade. A harp and finial mean you need a spider fitter. No harp, with the shade fixed straight to the socket, means you need an uno fitter.
| Fitter | How it attaches | Lamp needs | Good to know |
|---|---|---|---|
| Spider | Rests on the harp, locked with a finial | Harp, saddle and finial | Comes in drop, recessed and extended versions that change shade height |
| Uno | Threaded ring onto the socket | A socket made for uno shades, no harp | No harp or finial on show |
| Clip-on | Spring clip grips the bulb | Just a bulb | Made for E12 or E26 bulbs; pair with LED bulbs |
The wrong fitter can make a shade tilt, wobble or fail to attach at all. With clip-on shades, LED bulbs are the safer choice because incandescent bulbs can run hot enough to damage fabric.
Parts of a Lampshade: Frame, Rings, Liner and Diffuser
Lampshade parts are the frame, its two rings, and sometimes a liner or diffuser. The frame gives the shade its shape, with a top ring and a bottom ring joined by struts. The fitter is built into the top ring. Fabric shades often have a liner that hides the frame and bounces light down, and some shades add a diffuser, a disc of frosted material under the bulb that cuts glare.
Table Lamp Parts vs Floor Lamp Parts
Table lamp parts and floor lamp parts are almost identical. The differences come from height and how you use them.
| Feature | Table lamp | Floor lamp |
|---|---|---|
| Base | Smaller; the body often adds weight | Wide and weighted to prevent tipping |
| Threaded rod | Usually 1/8 IP | Often 1/4 IP in the base |
| Switch | Usually on the socket | On the socket, cord or a foot switch |
| Shade attachment | Harp and spider fitter, or uno | Uno fitter, harp, or a fixed shade |
| Extra parts | Neck, vase cap | Pole sections with couplings, sometimes an adjustable arm |
If you're shopping rather than repairing, keep these table lamp parts in mind: a lamp with a harp gives you the most freedom to change shades later.
What Lamps Are Made Of
Lamp bodies and bases come in a wide range of materials, and each one changes the weight, look and care of the lamp.
| Material | Look and feel | Practical notes |
|---|---|---|
| Brass | Warm metallic, classic or modern | Heavy and durable; unlacquered brass darkens over time |
| Ceramic | Glazed color and texture | Heavy, stable base; can chip if knocked |
| Glass | Clear, colored or frosted | Shows off the internal rod and cord, so those parts need to look neat |
| Alabaster | Soft, glowing stone | Diffuses light; heavier than it looks |
| Wood | Natural, warm | Lighter weight; often paired with a weighted base |
The hardware inside is usually metal no matter what the body is made of, so a ceramic or glass lamp still uses a standard rod, socket and harp.
Which Lamp Parts Can You Replace?
Most lamp parts are replaceable, and many use standard sizes. Before you start, always unplug the lamp.
| Repair | DIY level | Notes |
|---|---|---|
| Bulb, shade, finial | Easy | Match the bulb base and shade fitter |
| Harp or saddle | Easy | Measure the harp from saddle to top first |
| Felt pad | Easy | Peel and stick |
| Socket or socket switch | Moderate | Note which wire goes to which terminal before removing the old one |
| Cord and plug | Moderate | Replace with a polarized plug |
| Threaded rod or neck | Moderate | Bring the old part to match the thread size |
| Anything on a hardwired fixture | Call an electrician | Ceiling and wall fixtures are wired into the home circuit |
If a lamp has a cracked body, a burned socket or a cord that's brittle along its whole length, it may be worth replacing the lamp instead of the part.
Which Part to Check First
Once you know the parts of a lamp, most problems point to one part. A flickering light points to the socket or bulb, a tilting shade to the harp or fitter, and a wobble to the locknut under the base. The labeled diagram and the tables above give you the right name for each piece, so you can order the correct replacement the first time.
If you'd rather start fresh, explore table lamps and floor lamps at Residence Supply and choose one with the shade hardware that suits how you like to style it.