How to Install Wall Panels: Step by Step for Every Panel Type
Residence Supply |
How to install wall panels depends on the panel in your hands. Wood and MDF sheets go up with construction adhesive and finishing nails, interlocking PVC planks are screwed to the wall, and acoustic slat panels are screwed through their felt backing. The prep work is nearly the same for all of them.
Quick answer: Let the panels sit in the room before you start, clear the wall and mark the studs. Set the first panel plumb, cut the rest to fit, then fix each one with the adhesive or fasteners its maker calls for. Seal the joints with silicone in wet rooms and finish with trim.
Which Installation Method Fits Your Panel Type
| Panel type | How it attaches | Cut with | Worth knowing |
|---|---|---|---|
| Wood or MDF sheet paneling | Construction adhesive plus finishing nails into the studs | Fine-toothed saw | Trim each sheet 1/4 inch shorter than the ceiling |
| Interlocking PVC planks | Screws no more than 24 inches apart | Fine-tooth blade | Leave 1/4 inch of clearance at panel ends |
| PVC 3D tiles | Construction adhesive | Utility knife | Sand heavy wall texture smooth first |
| Peel and stick panels | Their own adhesive backing | Utility knife or box cutter | The wall must be smooth, clean and dry |
| Acoustic slat panels | Black screws through the felt, or adhesive | Fine-tooth saw for the slats, knife for the felt | Use screws on ceilings |
| Faux stone panels | Construction adhesive plus screws | Wood saw with a finish blade | Caulk and touch up the seams |
Each row comes from a manufacturer's or retailer's instructions for one product, and other brands set their own numbers. If the sheet that ships with your panels says something different, that's the one to follow.
Tools and Materials
Most wall panel installation jobs need the same short kit.
- Tape measure, pencil and level
- Stud finder
- Fine-toothed saw, plus a jigsaw for openings
- Utility knife
- Caulk gun and construction adhesive
- Rubber mallet
- Finishing nails or screws, depending on the panel
- Silicone sealant for wet rooms
- Circuit tester
- Safety goggles and a dust mask
Before You Start: Acclimate the Panels and Prep the Wall
Panels expand and contract, so they need time in the room before they go on the wall. How long depends on the material.
| Panel type | Time in the room before installing | Source |
|---|---|---|
| Sheet paneling | A few days | Home Depot |
| Wood paneling | At least 48 hours | Lowe's |
| Peel and stick wood planks | 48 to 72 hours | Stikwood |
| Interlocking PVC | At least 24 hours | Trusscore |
| Faux stone | At least 24 hours | Barron Designs |
While the panels rest, get the wall ready:
- Turn off the power to any outlet or switch on the wall and confirm it's off with a circuit tester.
- Remove the wall plates and pull any nails left in the wall.
- Take off the baseboards, crown moulding and trim you plan to reuse.
- Clean the wall. For thin panels, sand down heavy bumps or texture.
- On a wall that's uneven, cracked or rough, fasten a framework of 1x3 or 1x4 furring strips and fix the panels to that.
How Many Wall Panels to Buy
Measure the width and height of each wall and leave out the doors and windows. Divide the wall width by the width of one panel to get a count, then add 10 percent. Home Depot recommends that extra to cover waste and to help match color.
If you're still pricing the project, the guide to what wall panelling costs covers the budget side.
How to Install Wall Panels in 7 Steps
These steps follow the usual method for sheet and decorative paneling. Home Depot rates the job as intermediate and says it takes over a day.
1. Mark the Studs and Plan the Layout
Run a stud finder across the wall and mark where each stud sits. The nails or screws go into those marks later. Most guides start the first panel in a corner and work across the wall from there.
2. Set the First Panel Plumb
Hold the first panel in place and check it with a level before it's fixed. Every panel after it lines up against this one, so a first panel that leans will carry the lean across the whole wall.
3. How to Cut Wall Panels to Size
Trim each panel 1/4 inch shorter than the ceiling height. That gap gives the panel room to expand and contract, and the trim hides it. Use a fine-toothed blade so the face doesn't split or fray. HomeTips adds a rule for which way the panel faces while you cut: face up for a handsaw, face down for a power saw.
4. Cut Around Outlets and Switches
With the power off, make a paper template of each opening, lay it on the panel in the right spot and trace it. A jigsaw or oscillating saw makes the cutout.
A panel adds thickness to the wall, which leaves the electrical box sitting behind the new surface. Fine Homebuilding notes that code allows a box to sit back no more than 1/4 inch from a noncombustible surface, and that boxes must be completely flush with combustible surfaces such as wood paneling. A box extender brings the edge of the box forward. If you're unsure about this part, it's a job for an electrician.
5. Apply the Adhesive
Run construction adhesive across the back of the panel in a W or wave pattern with a caulk gun. Press the panel to the wall and tap it into place with a rubber mallet.
Read the adhesive label before you buy. Working and cure times vary by product. Liquid Nails Paneling and Molding Adhesive lists a 20 minute working time and a minimum cure of 24 hours, and Loctite Power Grab Ultimate lists a cure of 24 to 48 hours. Loctite also warns that some plastics can be hard to bond and says to test first, which matters for PVC panels.
6. Nail or Screw the Panel
Drive finishing nails through the panel into the studs you marked. Lowe's advises nailing wherever a plank lines up with a stud, even when you're using adhesive. On a plaster wall you may need to attach furring strips first and nail into those.
7. Finish the Seams, Corners and Trim
Cover the nail heads with wood putty. Glue and then nail the moulding back in place so it covers the gaps at the ceiling and floor. PVC systems use their own trim pieces: J trim at the edges, inside and outside corner trims, and an H trim where two panel ends meet.
How to Install PVC Wall Panels
PVC wall panels come in two main forms, and they install differently.
Interlocking planks are fastened with screws. Trusscore and Palram both call for a fastener at least every 24 inches, driven at least 1 inch into solid backing. Leave a minimum of 1/4 inch of clearance at the ends of panels and trims so the PVC can expand. Both makers recommend a fine-tooth blade installed in the reverse direction for cleaner cuts, and Trusscore warns that a reversed blade could be unsafe on other materials.
Glue-up PVC tiles skip the screws. DumaWall's US instructions recommend Loctite Power Grab Ultimate and list existing tile, drywall, cement board, OSB and plywood on framed walls as suitable surfaces. The tiles can be scored a few times with a utility knife and snapped at the line.
PVC 3D wall panels are thinner, so the wall behind them matters more. Ekena Millwork's instructions say to sand off excessive bumps or texture, clean the wall and the back of each panel, and cut with a utility knife. Seams can be filled with paintable caulk before painting.
For background on the material itself, see what a PVC wall panel is.
How to Install Peel and Stick Wall Panels
Peel and stick wall panels need the least equipment and the most careful wall prep.
- The wall must be smooth, even, clean and dry. Smart Tiles lists textured walls as unsuitable.
- Fresh paint needs time to cure before anything sticks to it. Smart Tiles says 21 days and RoomMates says up to three weeks.
- Clean the wall with a degreasing product such as TSP. Smart Tiles advises against dish soap, which can leave a slightly greasy film.
- Cut with a box cutter, using a ruler as the guide.
- Once a tile is where you want it, press firmly with a credit card or plastic smoother.
- Keep the maker's clearance from stoves. Smart Tiles asks for 8 inches behind a stove or cooktop.
Both makers say their tiles handle splashes or humid rooms, but they don't recommend them inside a shower.
How to Install Wood Wall Panels and Acoustic Slat Panels
Wood wall panels follow the seven steps above. Wood expands and contracts with humidity, so the gap matters. This Old House recommends a 3/8 inch gap around the edges of wood paneling.
Acoustic wall panels with a felt backing are fixed differently. The screws go through the black felt between the slats, and makers recommend black screws. The number varies by maker: Andor Willow recommends a minimum of 8 screws per panel and WoodUpp recommends 15. If the screws land in drywall alone, Andor Willow says to insert anchors first.
Adhesive also works on walls. The Wood Veneer Hub applies it in a zigzag along the length of the panel and holds the panel against the wall for 30 to 60 seconds. For the best sound absorption, the same guide mounts the panels on battens 45 mm thick, spaced every 30 cm (about 12 inches), which leaves an air gap behind the felt.
Cut the wood slats with a fine-tooth saw and the felt with a utility knife. More on how these panels perform is in the guide to how effective acoustic wall panels are.
Installing Wall Panels Over Tile, Textured Walls and Brick
Some PVC panels are made to go over tile, and DumaWall lists existing tile as a suitable surface. Lowe's notes that vinyl over tile needs the grout lines filled flush with the tiles first, because an uneven surface can show through. RoomMates allows peel and stick tiles over existing ceramic tile that is smooth and clean.
On a textured wall, thin panels and peel and stick products need the texture sanded smooth. For rigid panels on a rough wall, furring strips give a flat base.
On brick or concrete, HomeTips fastens furring strips to masonry with concrete nails, or with screws and masonry anchors, then fixes the panels to the strips. Check the panel's own limits too. DumaWall says its panels are not intended for raw concrete, poured concrete walls or concrete block basement walls.
The guide to PVC wall panels for bathrooms goes further into fitting panels over existing tile.
Wall Panels in Bathrooms and Kitchens
A splash zone needs less protection than a shower. Behind a vanity or along a kitchen wall, bathroom wall panels and kitchen wall panels rated for moisture need sealed edges. Palram recommends a one part, neutral cure silicone sealant at all corners and around fixtures.
Inside a shower, the wall behind the panel does part of the waterproofing. Trusscore's shower guide installs a backer such as cement board, applies a liquid waterproof membrane over it, and then runs a thin bead of silicone along the tongue of every panel, at the trims and in the corners. It also says to check local building codes. A shower wall panel should be one the maker rates for that use.
After sealing, keep the area dry while everything cures. One shower wall kit sold at Lowe's asks for a minimum of 24 hours.
Is It Better to Glue or Nail Wall Panels?
Most guides use both. Lowe's recommends construction-grade adhesive for planks and panels, with small finish nails to hold each piece while the adhesive dries. This Old House says adhesive can provide up to 30 percent of the bond, so fewer nails are needed, and that adhesive may be all a lightweight material like MDF requires.
The panel type settles it in some cases. Interlocking PVC planks are screwed, peel and stick panels use their own backing, and slat panels on a ceiling should be screwed.
Common Wall Panel Installation Mistakes
- Installing panels the day they arrive, before they've adjusted to the room.
- Fitting panels tight to the ceiling or to each other's ends with no room to expand.
- Cutting with a coarse blade, which can split or fray the face.
- Leaving an electrical box recessed behind a wood panel.
- Sticking peel and stick panels to fresh paint or a textured wall.
- Using a decorative panel inside a shower when it's only rated for splashes.
Browse the full range of wall panels to compare materials before you measure.