Shop the Black Friday sale

Black Friday Sale · 20% off storewide

Black Friday Sale · 20% off

Use codewith
Ends in
0d 00h 00m 00s
Ends 16. november 2026 kl. 23.59

Parts of a Lamp: A Labeled Guide to Every Component

Residence Supply |

A lamp looks simple until something stops working, or a new shade refuses to sit straight. That's usually when people go looking for the names of the parts of a lamp, because you can't buy a replacement harp or socket if you don't know what to call it.

Quick answer: Every table or floor lamp is built from three groups of parts. The electrical parts (socket, switch, cord, plug and bulb) make the light. The structural parts (base, body, neck and the threaded rod inside) hold everything together. The shade hardware (harp, saddle, fitter and finial) holds the lampshade in place.

Parts of a Lamp Diagram (Table and Floor Lamp)

The diagram below labels the parts you'll find on a typical table lamp with a harp and a spider-fitter shade. A floor lamp uses the same parts with a taller body and a heavier base, so the labels apply to both.

Parts of a LampTable lamp with harp and spider-fitter shadeFinialSpider fitterHarpSocketSaddleCheck ringBodyBaseFelt padShadeBulbSwitchNeckThreaded rod(hidden inside)CordPolarized plugresidencesupply.com
The parts of a lamp, labeled on a table lamp with a harp and spider-fitter shade.
Part What it does Where it sits Easy to replace?
Finial Locks the shade onto the harp Top of the harp Yes
Harp Holds the shade above the bulb Clips into the saddle Yes
Shade Diffuses light and hides the bulb Rests on the harp or socket Yes
Bulb Produces the light Screws into the socket Yes
Socket Holds the bulb and connects it to power Top of the neck Yes, with care
Switch Turns the light on and off On the socket, cord or base Yes, with care
Saddle Supports the harp Under the socket Yes
Neck Short tube that raises the socket Between body and socket Sometimes
Body The main decorative column Middle of the lamp No
Threaded rod Holds the lamp together and carries the cord Runs through the body Sometimes
Base Keeps the lamp stable Bottom of the lamp No
Cord and plug Bring power from the outlet Exit at the base Yes, with care

Electrical Parts of a Lamp

The electrical parts are the ones that turn power from your wall outlet into light. They're also the parts most likely to wear out, so they're worth knowing by name.

Socket: Shell, Insulating Sleeve and Interior

The socket holds the light bulb and connects it to the lamp's wiring. On most lamps it has three layers. The outer shell is the metal or plastic casing you see. Inside it sits an insulating sleeve, a collar that fits into the shell to prevent short circuits. The interior is the threaded cup the bulb screws into, with the screw terminals the cord wires attach to.

If a bulb flickers when you tap the lamp, the socket is often the first part to check.

Lamp Switch Types: Turn Knob, 3-Way, Pull Chain, Rotary and In-Line

A lamp switch can live on the socket, on the base or on the cord. Common versions include rotary, push-button, turn-knob, canopy, pull-chain and toggle switches. An in-line switch sits partway along the cord, which is handy when the socket is hard to reach.

Switch type Where you'll find it Best for
Turn knob Built into the socket Classic table lamps
Push-through Built into the socket Simple on/off
Pull chain Hangs from the socket Floor lamps and older fixtures
Rotary On the cord or base Lamps with a dimming option
In-line Partway along the cord Lamps with hard-to-reach sockets
3-way Built into the socket Three brightness levels

How a 3-Way Lamp Socket Works

A 3-way lamp gives you three brightness levels from one bulb. A 3-way incandescent bulb has two filaments that can be switched on separately or together. A common example is the 50/100/150 W bulb, which pairs a 50 W filament with a 100 W filament.

The socket has three electrical contacts instead of two. The extra one matches a ring-shaped contact on the bottom of a 3-way bulb. Put a standard bulb in a 3-way socket and it will only light on one or two of the clicks, because the ring contact has nothing to touch.

This is a different thing from a 3-way wall switch, which controls one ceiling light from two locations. If that's what you're wiring, the 3-way light switch wiring guide walks through it step by step.

Cord and Polarized Plug

The cord carries electricity from the outlet up through the lamp to the socket. Look at the plug on most modern lamps and you'll see one blade is wider than the other. That's a polarized plug, designed to help keep electricity from leaking to the metal parts of the lamp.

Inside the socket, many lamps also have an Underwriter's knot (UL knot) tied in the cord. It gives strain relief to the screw terminals, so a tug on the cord doesn't pull the wires loose.

Bulb and Bulb Base (E26, E12)

The bulb is the only part you'll replace regularly, and the base is what decides whether it fits. The "E" in a base code stands for Edison screw, and the number is the base diameter in millimeters. E26 is the standard medium base used in most North American lamps, while E12 is the smaller candelabra base, about 12 mm across, used mostly for decorative lighting.

For shapes, color temperature and brightness, see the guide to choosing the right light bulbs.

Structural Parts: Base, Body, Neck and Threaded Rod

The structural parts carry the lamp's weight and give it its look. Most of them are threaded onto one hidden rod, which is why a wobbly lamp can usually be fixed by tightening a single nut underneath.

Base and Felt Pad

The base is the bottom of the lamp and its main job is stability. Floor lamps need a wider, heavier base than table lamps because they're tall and easy to knock. Underneath, many lamps have a felt pad that protects furniture from scratches and covers the nut that holds the lamp together.

Body or Column

The body (also called the column) is the decorative middle of the lamp. It's the part that defines the style, whether that's a ceramic gourd, a glass column or a brass stem. If you're comparing materials, brass and alabaster each age and diffuse light differently.

Neck, Check Ring and Vase Cap

Between the body and the socket you'll often find a short neck, a decorative tube that lifts the socket to the right height. A check ring is a small ring that sits on the threaded rod and finishes off a joint. A vase cap sits over the opening of a vase-style body, so the rod and cord can pass through cleanly.

Threaded Rod (Lamp Pipe), Locknut and Washers

Hidden inside nearly every lamp is a hollow threaded rod, also called lamp pipe. It typically anchors the lamp together, with the other parts threaded onto it, and the cord runs up through its center.

The most common size is 1/8 IP, which has a 3/8 inch outside diameter. Its thread is always 27 threads per inch. Larger 1/4 IP pipe, with a 1/2 inch outside diameter, shows up on floor lamps and floor lamp bases. A locknut and washers at the bottom of the rod clamp everything tight.

Thread size Outside diameter Where it's used
1/4-27 7/32 inch Harp tops and most finials
1/8 IP 3/8 inch Most table lamp rods, necks and sockets
1/4 IP 1/2 inch Floor lamps and floor lamp bases

Lampshade Parts and Fitters

The shade hardware is where most "why won't this shade fit?" problems start. A fitter is the metal framework inside the top of a shade that attaches it to the lamp, harp or socket. There are three main types, and each one needs different hardware on the lamp.

Lamp Harp and Saddle

A lamp harp is the U-shaped metal frame that arcs over the bulb and holds the shade. Its legs clip into a saddle, the part that sits on the lamp just below the socket.

Harps come in different heights, and the right one lets the shade cover the socket and bulb without touching the base. To size one, measure from the saddle to the top of the harp. If your shade sits too high and shows the socket, a shorter harp is usually the fix.

Finial: The Top of the Lamp

The piece at the very top of a lamp is the finial. It's a decorative fitting that secures the shade to the harp. Most finials screw onto a 1/4-27 thread, which is why they're easy to swap for a different style. For the history and design side of finials, see finials explained.

Spider vs Uno vs Clip-On Fitters

Check what your lamp has before you buy a new shade. A harp and finial mean you need a spider fitter. No harp, with the shade fixed straight to the socket, means you need an uno fitter.

Fitter How it attaches Lamp needs Good to know
Spider Rests on the harp, locked with a finial Harp, saddle and finial Comes in drop, recessed and extended versions that change shade height
Uno Threaded ring onto the socket A socket made for uno shades, no harp No harp or finial on show
Clip-on Spring clip grips the bulb Just a bulb Made for E12 or E26 bulbs; pair with LED bulbs

The wrong fitter can make a shade tilt, wobble or fail to attach at all. With clip-on shades, LED bulbs are the safer choice because incandescent bulbs can run hot enough to damage fabric.

Parts of a Lampshade: Frame, Rings, Liner and Diffuser

Lampshade parts are the frame, its two rings, and sometimes a liner or diffuser. The frame gives the shade its shape, with a top ring and a bottom ring joined by struts. The fitter is built into the top ring. Fabric shades often have a liner that hides the frame and bounces light down, and some shades add a diffuser, a disc of frosted material under the bulb that cuts glare.

Table Lamp Parts vs Floor Lamp Parts

Table lamp parts and floor lamp parts are almost identical. The differences come from height and how you use them.

Feature Table lamp Floor lamp
Base Smaller; the body often adds weight Wide and weighted to prevent tipping
Threaded rod Usually 1/8 IP Often 1/4 IP in the base
Switch Usually on the socket On the socket, cord or a foot switch
Shade attachment Harp and spider fitter, or uno Uno fitter, harp, or a fixed shade
Extra parts Neck, vase cap Pole sections with couplings, sometimes an adjustable arm

If you're shopping rather than repairing, keep these table lamp parts in mind: a lamp with a harp gives you the most freedom to change shades later.

What Lamps Are Made Of

Lamp bodies and bases come in a wide range of materials, and each one changes the weight, look and care of the lamp.

Material Look and feel Practical notes
Brass Warm metallic, classic or modern Heavy and durable; unlacquered brass darkens over time
Ceramic Glazed color and texture Heavy, stable base; can chip if knocked
Glass Clear, colored or frosted Shows off the internal rod and cord, so those parts need to look neat
Alabaster Soft, glowing stone Diffuses light; heavier than it looks
Wood Natural, warm Lighter weight; often paired with a weighted base

The hardware inside is usually metal no matter what the body is made of, so a ceramic or glass lamp still uses a standard rod, socket and harp.

Which Lamp Parts Can You Replace?

Most lamp parts are replaceable, and many use standard sizes. Before you start, always unplug the lamp.

Repair DIY level Notes
Bulb, shade, finial Easy Match the bulb base and shade fitter
Harp or saddle Easy Measure the harp from saddle to top first
Felt pad Easy Peel and stick
Socket or socket switch Moderate Note which wire goes to which terminal before removing the old one
Cord and plug Moderate Replace with a polarized plug
Threaded rod or neck Moderate Bring the old part to match the thread size
Anything on a hardwired fixture Call an electrician Ceiling and wall fixtures are wired into the home circuit

If a lamp has a cracked body, a burned socket or a cord that's brittle along its whole length, it may be worth replacing the lamp instead of the part.

Which Part to Check First

Once you know the parts of a lamp, most problems point to one part. A flickering light points to the socket or bulb, a tilting shade to the harp or fitter, and a wobble to the locknut under the base. The labeled diagram and the tables above give you the right name for each piece, so you can order the correct replacement the first time.

If you'd rather start fresh, explore table lamps and floor lamps at Residence Supply and choose one with the shade hardware that suits how you like to style it.

FAQ

Questions, Answered.

What are the 7 main types of lamps?

There's no single official list of seven, but the lamp types most people mean are table lamps, floor lamps, desk lamps, bedside lamps, buffet lamps, wall-mounted lamps (sconces) and torchiere floor lamps. They share the same basic parts, including a socket, switch, cord, base and body. The differences come from height, shade style and where the switch sits. Desk lamps often add an adjustable arm, and torchieres throw light up toward the ceiling instead of using a fabric shade.

Are lamp parts universal?

Many lamp parts follow standard sizes, so they're more interchangeable than people expect, but not everything fits everything. Most table lamps use a 1/8 IP threaded rod, and most finials use a 1/4-27 thread, which makes sockets, necks and finials easy to match. Harps vary by height, and shades vary by fitter type, so measure the harp and check whether you need a spider, uno or clip-on fitter before ordering. When in doubt, bring the old part with you to compare.

What is the top of a lamp called?

The top of a lamp is called the finial. It's the small decorative cap that screws onto the top of the harp and holds a spider-fitter shade in place. Most finials thread onto a 1/4-27 stem, so swapping one for a different style takes seconds and no tools. Lamps with an uno or clip-on shade usually have no finial, because the shade attaches directly to the socket or the bulb instead of resting on a harp. If you're buying a replacement finial, check the thread size before ordering.

What size harp does my lamp need?

Most table lamps use a harp between 7 and 10 inches tall, while floor lamps typically take 8 to 12 inches, and oversized shades can need more. The right harp sits about half an inch to an inch above the shade's fitter, which leaves room for the finial. A harp that's too tall leaves an awkward gap, and one that's too short makes the shade sit low. To check your current harp, measure from the saddle to the top of the harp, then compare that with how your shade sits.

How do you replace a lamp socket?

Start by unplugging the lamp, then take the old socket apart and disconnect the two cord wires. Before connecting the new socket, find the neutral wire, which has raised ribs or markings along its insulation. Hook the ribbed neutral wire clockwise around the silver screw and the smooth hot wire clockwise around the brass screw. Tie the cord ends in a simple knot for strain relief, slide the sleeves back over the socket, reassemble the lamp and test it with a bulb. If the cord is cracked or brittle, replace it at the same time.

Still have questions? Our team is here to help.

Contact Support